View SN751508_1113753.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SN751508, SN751518 DC PLASMA DISPLAY DRIVERS
SLDS035 - JANUARY 1987 - REVISED NOVEMBER 1989
D D D D D D
Each Device Drives 32 Lines -120-V PNP Open-Collector Parallel Outputs High-Speed Serially Shifted Data Inputs CMOS-Compatible Inputs Strobe and Sustain Inputs Provided Serial Data Output for Cascade Operation
SN751508 . . . FT PACKAGE (TOP VIEW)
description
The SN751508 and SN751518 are monolithic integrated circuits designed to drive the data lines of a dc plasma panel display. The SN751518 pin sequence is reversed from the SN751508 for ease in printed-circuit-board layout. Each device consists of two 16-bit shift registers, 32 latches, 32 OR gates, and 32 pnp opencollector output AND gates. Typically, a 32-bit data string is split into two 16-bit data strings externally and then entered in parallel into the shift registers on the high-to-low transition of the clock signal. A high LATCH ENABLE transfers the data from the shift registers to the inputs of 32 OR gates through the latches. Data present in the latch during the high-to-low transition of LATCH ENABLE is stored. When STROBE is high, the latch is masked and a high is placed on the data input of the output AND gates. When STROBE is low and SUSTAIN is high, data from the latches is reflected at the outputs. When low, SUSTAIN forces all outputs to their off state. Drivers can be cascaded via the serial data outputs of the static shift registers. These outputs are not affected by LATCH ENABLE, STROBE, or SUSTAIN. The SN751508 and the SN751518 characterized from 0C to 70C. are
Q32 Q31 Q30 Q29 Q28 Q27 Q26 Q25 Q24 Q23 Q22 Q21 Q20 Q19 Q18 Q17 GND NC STROBE NC CLOCK VCC SERIAL OUT2 SERIAL OUT1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25
Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q9 Q10 Q11 Q12 Q13 Q14 Q15 Q16 GND SUSTAIN NC LATCH ENABLE NC VCC DATA IN2 DATA IN1
SN751518 . . . FT PACKAGE (TOP VIEW)
Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q9 Q10 Q11 Q12 Q13 Q14 Q15 Q16 GND SUSTAIN NC LATCH ENABLE NC VCC DATA IN2 DATA IN1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25
Q32 Q31 Q30 Q29 Q28 Q27 Q26 Q25 Q24 Q23 Q22 Q21 Q20 Q19 Q18 Q17 GND NC STROBE NC CLOCK VCC SERIAL OUT2 SERIAL OUT1
NC - No internal connection
PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.
Copyright (c) 1989, Texas Instruments Incorporated
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
1
SN751508, SN751518 DC PLASMA DISPLAY DRIVERS
SLDS035 - JANUARY 1987 - REVISED NOVEMBER 1989
logic symbols
SN751508
SUSTAIN STROBE LATCH ENABLE CLOCK 31 19 29 21 EN44 V43 C42 Z40 CMOS/EL DISP
SRG16 40(C41/) DATA IN1 25 41D Z1 Z3 1 2 3 4 42D 42D 42D 42D 43, 44 43, 44 43, 44 43, 44 48 47 46 45 Q1 Q2 Q3 Q4
. . . . . .
SRG16 40(C45/) DATA IN2 26 45D
Z15 Z17 15 16 Z29 17 Z31 18 42D 42D 42D 42D
. . .
. . .
43, 44 43, 44 43, 44 43, 44
34 33 16 15
. . .
. . .
4 3 2 1 24
Q15 Q16 Q17 Q18
Z2
. . . . . .
Z4
29 30 31 32
42D 42D 42D 42D
43, 44 43, 44 43, 44 43, 44
Q29 Q30 Q31 Q32 SERIAL OUT1
Z16 Z18 31 1 Z30 32 Z32
23
SERIAL OUT2
SN751518
SUSTAIN STROBE LATCH ENABLE CLOCK 18 30 20 28 EN44 V43 C42 Z40 SRG16 40(C41/) 41D CMOS/EL DISP
DATA IN1
24
. . . . . .
SRG16 40(C45/) DATA IN2 23 45D
Z1 Z3
1 2 3 4
42D 42D 42D 42D
43, 44 43, 44 43, 44 43, 44
1 2 3 4
Z15 Z17 15 16 Z29 17 Z31 18 42D 42D 42D 42D
. . .
. . .
Q1 Q2 Q3 Q4
43, 44 43, 44 43, 44 43, 44
15 16 33 34
. . .
. . .
45 46 47 48 25
Q15 Q16 Q17 Q18
. . . . . .
Z2 Z4
29 30 31 32
42D 42D 42D 42D
43, 44 43, 44 43, 44 43, 44
1
Q29 Q30 Q31 Q32 SERIAL OUT1
Z16 Z18 31
1
Z30 32 Z32
26
SERIAL OUT2
These symbols are in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.
2
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
SN751508, SN751518 DC PLASMA DISPLAY DRIVERS
SLDS035 - JANUARY 1987 - REVISED NOVEMBER 1989
logic diagram (positive logic)
SUSTAIN
STROBE
LATCH ENABLE CLOCK Shift Register 1 1D C1 R1
Latches C2 2D LC1 Q1
DATA IN1
1D C1 R3
C2 2D LC2
Q2
. . .
. . .
1D C1 R29
C2 2D LC3
Q3
C2 1D C1 R31 2D LC4
Q4
. . .
DATA IN2
Shift Register 2 1D C1 R2
..... ..... .....
. . .
. . .
Q29
C2 2D LC29
1D C1 R4 C2 2D LC30 Q30
. . .
. . .
1D C1 R30
C2 2D LC31
Q31
1D C1 R32
C2 2D LC32
Q32
SERIAL OUT1 SERIAL OUT2
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
3
SN751508, SN751518 DC PLASMA DISPLAY DRIVERS
SLDS035 - JANUARY 1987 - REVISED NOVEMBER 1989
FUNCTION TABLE CONTROL INPUTS FUNCTION CLOCK No X X X X LATCH ENABLE X X L H X X STROBE X X X X L H SUSTAIN X X X X H H SHIFT REGISTERS R1 THRU R32 Load and shift No change As determined above As determined above As determined above LATCHES LC1 THRU LC32 Determined by LATCH ENABLE Stored data New data Determined by LATCH ENABLE Determined by LATCH ENABLE OUTPUTS SERIAL S01 R31 S02 R32 Q1 THRU Q32 Determined by y SUSTAIN and STROBE Determined by y SUSTAIN and STROBE LC1 thru LC32 All on (high)
Load Latch Enable Strobe
R31
R32
R31
R32
Sustain
X
X
X
L
R31
R32
All off
H = high level, L = low level, X = irrelevant, = high-to-low transition Each even-numbered shift register stage takes on the state of the next-lower even-numbered stage, and likewise each odd-numbered shift register stage takes on the state of the next-lower odd-numbered stage; i.e., R32 takes on the state of R30, R30 takes on the state of R28, ... R4 takes on the state of R2, R2 takes on the state of DATA IN2, R31 takes on the state of R29, R29 takes on the state of R27, ... R3 takes on the state of R1, and R1 takes on the state on DATA IN1. New data enters the latches while LATCH ENABLE is high. This data is stored while LATCH ENABLE is low.
typical operating sequence
...
CLOCK
DATA IN Shift Register Contents LATCH ENABLE
Valid
Irrelevant
Invalid
Valid
Latch Contents STROBE
Previously Stored Data
New Data Valid
SUSTAIN
Q Outputs
Off State
Valid
Off State
4
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
SN751508, SN751518 DC PLASMA DISPLAY DRIVERS
SLDS035 - JANUARY 1987 - REVISED NOVEMBER 1989
schematics of inputs and outputs
EQUIVALENT OF EACH INPUT VCC TYPICAL OF ALL Q OUTPUTS VCC2 TYPICAL OF SERIAL OUTPUT VCC
Input
Output
Output
GND
GND
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage range, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 0.4 to 7 V On-state Q output voltage range, VO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 120 V to VCC + 0.4 V Input voltage range, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 0.4 V to VCC + 0.4 V Serial output voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 0.4 V to VCC + 0.4 V Continuous total power dissipation at (or below) 25C free-air temperature (see Note 2) . . . . . . . . 1025 mW Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0C to 70C Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65C to 150C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260C
NOTES: 1. Voltages values are with respect to GND. 2. For operation above 25C free-air temperature, derate linearly to 656 mW at 70C at the rate of 8.2 mW/C.
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
5
SN751508, SN751518 DC PLASMA DISPLAY DRIVERS
SLDS035 - JANUARY 1987 - REVISED NOVEMBER 1989
recommended operating conditions
MIN Supply voltage, VCC Output voltage, VO High-level High level input voltage, VIH voltage Low-level Low level input voltage VIL voltage, Output current, IO (TA = 25C) Clock frequency, fclock CLOCK DATA IN Pulse duration, tw (see Figure 1) LATCH ENABLE STROBE SUSTAIN DATA IN before CLOCK CLOCK low before LATCH ENABLE Setup time, tsu (see Figure 1) LATCH ENABLE low before CLOCK LATCH ENABLE high before STROBE LATCH ENABLE high before SUSTAIN Hold time, DATA IN after CLOCK, th (see Figure 1) Operating free-air temperature, TA 75 160 90 2 2 20 50 0 0 0 50 0 70 s C ns s ns VCC = 4.5 V VCC = 5.5 V VCC = 4.5 V VCC = 5.5 V 3.6 4.4 0.9 1 - 1.2 5 4.5 NOM 5 MAX 5.5 - 75 UNIT V V V V mA MHz
electrical characteristics over operating free-air temperature range, VCC = 5 V (unless otherwise noted)
PARAMETER Q outputs VOH High-level output voltage TEST CONDITIONS IOH = - 0.5 mA VCC = 5 5 V 5.5 SERIAL OUT 1, 2 1 VCC = 4 5 V 4.5 VCC = 5 5 V 5.5 VOL Low-level Low level output voltage SERIAL OUT 1, 2 1 VCC = 4 5 V 4.5 IOH IOL IIH IIL ICC High-level Q output current Low-level Q output current High-level input current Low-level input current Supply current TA= 25C, TA= 25C, TA= 25C, TA= 25C, All Q outputs high, All Q outputs low IOH = - 100 A IOH = - 20 A IOH = - 100 A IOH = - 20 A IOL = 100 A IOL = 20 A IOL = 100 A IOL = 20 A VO = 3 V VO = - 75 V VI = VCC VI = 0 VCC = 5.5 V 17 - 1.2 - 500 1 -1 25 3 15 MIN 4 4.3 4.4 3.4 3.6 0.9 0.9 1.2 1.1 1.1 0.9 mA A A A mA pF V 3.6 TYP 4.5 4.6 V MAX UNIT
Ci Input capacitance All typical values are at TA = 25C.
6
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
SN751508, SN751518 DC PLASMA DISPLAY DRIVERS
SLDS035 - JANUARY 1987 - REVISED NOVEMBER 1989
switching characteristics, VCC = 5 V, CL = 15 pF, TA = 25C
PARAMETER tpd tDLH tDHL tTLH Propagation delay time, CLOCK to SERIAL OUT Delay time, low-to-high-level Q output from SUSTAIN or STROBE Delay time, high-to-low-level Q output from SUSTAIN or STROBE Transition time, low-to-high-level Q output RL = 91 k, See Figures 1 and 2 TEST CONDITIONS MIN TYP 100 0.3 1 2 11 MAX 150 1 2.5 5 18 UNIT ns s s s s
tTHL Transition time, high-to-low-level Q output Typical values for delay times are measured from SUSTAIN.
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
7
SN751508, SN751518 DC PLASMA DISPLAY DRIVERS
SLDS035 - JANUARY 1987 - REVISED NOVEMBER 1989
PARAMETER MEASUREMENT INFORMATION
4V CLOCK tw tsu DATA IN tw th 4V 50% 1V tw tpd VOH SERIAL OUT 50% VOL tsu tw 4V LATCH ENABLE 50% 1V tsu tw STROBE 50% 1V tsu tw tw 4V SUSTAIN 50% 1V tDLH tDLH tDHL tDLH tDLH On tw 4V tsu 50% 1V
90% Q Outputs 10% tTLH tTLH tTHL NOTE: Input tr and tf are less than or equal to 10 ns. tTHL tTLH
Off
Figure 1. Input Timing and Switching Time Voltage Waveforms
8
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
SN751508, SN751518 DC PLASMA DISPLAY DRIVERS
SLDS035 - JANUARY 1987 - REVISED NOVEMBER 1989
PARAMETER MEASUREMENT INFORMATION
5V VCC Generator (see Note A) DATA IN Q1 91 k 15 pF - 75 V
Generator (see Note A)
CLOCK
Q2
. . .
Generator (see Note A)
STROBE Q31
Generator (see Note A)
SUSTAIN Q32
Generator (see Note A)
LATCH ENABLE SERIAL OUT1 SERIAL OUT2 GND CL CL
CL = 15 pF (see Note B) TEST CIRCUIT NOTES: A. Input pulses are supplied by generators having the following characteristics: tw = 100 ns, PRR 5 MHz, tr 10 ns, tf 10 ns, ZO = 50 . B. CL includes probe and jig capacitance.
Figure 2. Test Circuit
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
9
SN751508, SN751518 DC PLASMA DISPLAY DRIVERS
SLDS035 - JANUARY 1987 - REVISED NOVEMBER 1989
TYPICAL CHARACTERISTICS
SUPPLY CURRENT vs FREE-AIR TEMPERATURE
20 VCC = 5.5 V All Q Outputs Low No Load I ICC - Supply Current - mA CC 15
tPD - Propagation Delay Time, CLOCK to SERIAL OUT - ns t pd
PROPAGATION DELAY TIME, CLOCK TO SERIAL OUT vs FREE-AIR TEMPERATURE
125
100
75
10
50
t DLH - Delay Time, Q Output, Low to High - s
0.4
t DHL - Delay Time, Q Output, High to Low - s
10
AA AA
5
25 VCC = 5 V CL = 15 pF 0 0 10 20 30 40 50 60 70 80 TA - Free-Air Temperature - C
0 0 10 20 30 40 50 60 70 80 TA - Free-Air Temperature - C
Figure 3
DELAY TIME, SUSTAIN INPUT TO Q OUTPUT LOW TO HIGH vs FREE-AIR TEMPERATURE
0.5 VCC = 5 V CL = 15 pF RL = 91 k 2 VCC = 5 V CL = 15 pF RL = 91 k 1.5
Figure 4
DELAY TIME, SUSTAIN INPUT TO Q OUTPUT HIGH TO LOW vs FREE-AIR TEMPERATURE
0.3
1
0.2
0.5
0.1
0 0 10 20 30 40 50 60 70 80 TA - Free-Air Temperature - C
0 0 10 20 30 40 50 60 70 80 TA - Free-Air Temperature - C
Figure 5
Figure 6
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
SN751508, SN751518 DC PLASMA DISPLAY DRIVERS
SLDS035 - JANUARY 1987 - REVISED NOVEMBER 1989
TYPICAL CHARACTERISTICS
TRANSITION TIME, Q OUTPUT, LOW TO HIGH vs FREE-AIR TEMPERATURE
tTLH s t TLH - Transition Time, Q Output, Low to High - us 5 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 0 10 20 30 40 50 60 70 80 TA - Free-Air Temperature - C VCC = 5 V CL = 15 pF RL = 91 k ttTHL - Transition Time, Q Output, High to Low - uss THL 20 VCC = 5 V CL = 15 pF RL = 91 k 15
TRANSITION TIME, Q OUTPUT, HIGH TO LOW vs FREE-AIR TEMPERATURE
10
5
0 0 10 20 30 40 50 60 70 80 TA - Free-Air Temperature - C
Figure 7
Figure 8
POST OFFICE BOX 655303
* DALLAS, TEXAS 75265
11
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Interface Logic Power Mgmt Microcontrollers Low Power Wireless amplifier.ti.com dataconverter.ti.com dsp.ti.com interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti.com/lpw Applications Audio Automotive Broadband Digital Control Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2007, Texas Instruments Incorporated
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Interface Logic Power Mgmt Microcontrollers Low Power Wireless amplifier.ti.com dataconverter.ti.com dsp.ti.com interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti.com/lpw Applications Audio Automotive Broadband Digital Control Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2007, Texas Instruments Incorporated
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Interface Logic Power Mgmt Microcontrollers Low Power Wireless amplifier.ti.com dataconverter.ti.com dsp.ti.com interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti.com/lpw Applications Audio Automotive Broadband Digital Control Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2007, Texas Instruments Incorporated
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Interface Logic Power Mgmt Microcontrollers Low Power Wireless amplifier.ti.com dataconverter.ti.com dsp.ti.com interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti.com/lpw Applications Audio Automotive Broadband Digital Control Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2007, Texas Instruments Incorporated
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Interface Logic Power Mgmt Microcontrollers Low Power Wireless amplifier.ti.com dataconverter.ti.com dsp.ti.com interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti.com/lpw Applications Audio Automotive Broadband Digital Control Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2007, Texas Instruments Incorporated
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Interface Logic Power Mgmt Microcontrollers Low Power Wireless amplifier.ti.com dataconverter.ti.com dsp.ti.com interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti.com/lpw Applications Audio Automotive Broadband Digital Control Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2007, Texas Instruments Incorporated
PACKAGE OPTION ADDENDUM
www.ti.com
24-Jun-2005
PACKAGING INFORMATION
Orderable Device SN751508FT SN751518FT SN751518FT
(1)
Status (1) OBSOLETE OBSOLETE OBSOLETE
Package Type DFP DFP DFP
Package Drawing FT FT FT
Pins Package Eco Plan (2) Qty 48 48 48 TBD TBD TBD
Lead/Ball Finish Call TI Call TI Call TI
MSL Peak Temp (3) Call TI Call TI Call TI
The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Interface Logic Power Mgmt Microcontrollers RFID Low Power Wireless amplifier.ti.com dataconverter.ti.com dsp.ti.com interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lpw Applications Audio Automotive Broadband Digital Control Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2007, Texas Instruments Incorporated

▲Up To Search▲

Price & Availability of SN751508

	To Download SN751508 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .